Dairy powders: flow properties and performance outcomes
Dairy powders present a concentrated version of almost every powder flow challenge. This article explains the specific testing approach for whole milk powder, skimmed milk powder, whey, and infant formula base.
Why dairy powders are among the most demanding to handle
Spray-dried dairy powders - whole milk powder, skimmed milk powder, whey protein concentrate, and infant formula base blends - are produced at scale and filled into containers with tight weight tolerances. They are hygroscopic, caking-prone, and sensitive to the humidity conditions of the filling hall. Their cohesive properties change with moisture content, temperature, and handling history. And for infant formula specifically, fill weight accuracy is not just a commercial concern - it is a regulatory requirement, with permitted variation limits that are narrower than most other food products.
At the same time, dairy powders must reconstitute reliably. A powder that clumps during reconstitution - because its cohesion is too high, or because it has partially caked during storage - fails its primary functional purpose regardless of how accurately it was filled. The connection between powder flow properties and reconstitution behaviour is direct: the same inter-particle bonding that causes caking also causes lumping on dissolution.
|
The dairy powder challenge Dairy powders must flow freely enough to fill accurately, pack consistently enough to meet weight tolerances, remain stable enough during storage to reconstitute cleanly, and achieve all of this across the humidity range of a real production environment - not just laboratory ambient conditions. |
The hygroscopic challenge - how humidity changes flow properties
Dairy powders are hygroscopic - they adsorb moisture from the atmosphere, and that moisture changes inter-particle forces. At low moisture levels, lactose on the particle surface is amorphous and relatively non-sticky. As moisture increases - from the environment or from condensation during temperature changes - amorphous lactose crystallises. Crystallisation releases water, further increasing local humidity, and the crystalline bridges that form at particle contacts are the primary caking mechanism in dairy powders.
This means that dairy powder flow properties measured at laboratory ambient conditions may not represent behaviour in the filling hall during warm humid weather. A powder that flows acceptably at 40% relative humidity may begin to cake at 60% RH - and caking can develop over the course of a single shift if conditions change.
Running PFA cohesion and consolidation tests on powder conditioned at multiple relative humidity levels - typically 40%, 55%, and 70% RH - produces a humidity sensitivity profile that predicts at what conditions unacceptable caking or flow degradation will develop. This information drives environmental control specifications for the filling hall and storage area.
Fill weight accuracy - speed sensitivity and head load effects
Infant formula and premium dairy powder filling lines operate at high speeds with tight weight tolerances. Two dynamic flow properties determine whether fill weight accuracy is achievable at the target line speed.
Speed sensitivity: if the powder's resistance changes with filling head speed, fill weights will drift as machine speed changes. The PFSD Speed Sensitivity Ratio characterises this directly. A dairy powder with SSR close to 1.0 delivers consistent fill weights across the operating speed range. One with SSR above 1.0 will produce declining fill weights as throughput increases.
Head load sensitivity: as the hopper empties through a campaign, the weight of powder above the outlet decreases and the packing state near the outlet changes. If the powder is compressible, apparent bulk density decreases as the hopper empties, and fill weights drift downward toward the end of a hopper cycle. PFA compressibility testing characterises this through % Compressibility and Elastic Recovery.
Storage stability - caking in bulk storage
Dairy powder in bulk storage - in silos, big bags, or palletised retail containers - experiences continuous load from the material above it. Over days and weeks, this load combined with humidity and temperature cycling drives progressive consolidation. The Consolidation and Caking rig replicates this directly: a conditioned powder bed held under a defined static load for a controlled dwell time, with Work to Break measured after the dwell period.
For dairy powders, this test is particularly valuable when comparing batches. A batch with elevated Work to Break at a standard dwell time is a batch that will cause more handling problems in the warehouse and more difficult reconstitution in the consumer's cup. The test also provides the objective data needed to evaluate anti-caking agents - comparing Work to Break values for treated and untreated powder at the same dwell time.
| Dairy storage risk | Relevant PFA test |
| Humidity-driven crystalline bridge formation |
Cohesion + Consolidation rig at elevated RH - compare vs dry condition baseline |
| Progressive densification under bulk load |
Compressibility - % Compressibility and Relaxation at stresses representative of silo load |
| Restart difficulty after extended storage |
Consolidation rig - Work to Break at dwell times matching realistic storage durations |
| Batch-to-batch caking variation |
Caking test - Cake Height Ratio and Mean Cake Strength for each batch vs reference |
The reconstitution connection
For infant formula specifically, the Texture Analyser on the same instrument platform as the PFA measures lump strength in reconstituted formula - the force required to break reconstituted agglomerates. A formula with high PFA Cohesion Index tends to produce stronger, harder-to-disperse lumps on reconstitution. This connection between powder characterisation and finished product performance is precisely what the integrated PFA and Texture Analyser platform provides - flow properties and reconstitution quality from the same instrument, in the same laboratory session.